Valve adjusting tool This tool is necessary for adjusting valve clearance. Yamaha dealer immediately and have overloaded scooter may result the tire replaced. Have a Yamaha dealer check the vehicle. Spark plug cables in bad condition and leaking check for spark leakage in the dark 5. If the fuse immediately blows again, have a Yamaha dealer check the 1.
Rear brake lever free play tained as described, have a Yamaha dealer make this adjustment. Consult a Yamaha dealer for advice on place and, if necessary, protect it 4. Battery damaged or nearly discharged, should have 12. Using this repair manual is an inexpensive way to keep you vehicle working properly. Spark plugs in bad condition or partially fouled.
To download your manual please click on the links below. Repair and maintenance work attempted by anyone without this knowledge is likely to render the vehicle unsafe and unfit for use. Use only the appropriate special tools as this will help prevent damage caused by the use of inappropri- ate tools or improvised techniques. A stuck bent or burnt valve. If a brake pad has worn to the limit line, have a Yamaha dealer replace Checking the front brake pads point that the wear indicator almost the brake shoes as a set. Engine oil level check window 2.
Record the information on this label in the space provided. Check the brake fluid level regularly and fill as required. Replace spark plugs with new ones and check for spark. Elsewhere, Yamaha redesigned the Vino logo, reshaped the seat, simplified the floorboard and mildly reshaped the back end. Other brands may be similar in function and appearance, but infe- rior in quality. Start the engine, and then let it idle If any leakage is found, have a Yamaha 32 Nm 3. Using this repair manual is an inexpensive way to keep your vehicle working properly.
Therefore, carburetor adjust- Kickstarter bolt: throttle grip. Spark plugs in bad condition or have an improper gap or are partially fouled. Faulty fuel pump or fuse or relay. The tripmeter check the electrical circuit. Check for engine trouble codes. Fuel tank cap lock cover 1. Use a strong cord to secure any luggage to the carriers.
On the front half of the scooter, new telescopic forks replaced the older leading link design and five spoke rims replaced the older 3 spoke design which were actually lifted from the. The general shape and headlight array were left intact, but once you dig a little deeper there are lot of small changes to be found. Over the years the Vino 125 was kept unchanged, save for varying color options colors listed at bottom of page. This information will be needed to order spare parts. Tip over sensor needs a reset. Good luck and have a wonderful day. Insert the key in the lock, and then from the helmet holder, and then turn it as shown.
Check intake manifold and seals for leaks and cracks. Valve springs floating, weak, or broken. . On most scooters these two things compete for the volume under the seat and in the Vino 125 the storage is the clear winner. While pulling the rear brake lever off.
Front brake lever page 3-4 8. So visit your authorized Yamaha dealer to get all the facts. As you may suspect, the Vino 125 has a nice large storage area for your full face helmet under the seat. Do not exceed the maximum load of 75 kg 165 lb for the ve- hicle. Any damage, fluid leakage or loss of tire air pressure could have serious consequences. An abbreviation and symbol in the upper right corner of each page indicate the current chapter. Do not use warm water since it in- detergent, and a soft, clean sponge, and 6.
It represents the high degree of craftsmanship and reli- ability that have made Yamaha a leader in these fields. If you believe your battery might still be serviceable remove it from the bike and put it on a 1 or 2 amp trickle charger for 24 hours. When installing a circlip 1, make sure the sharp-edged corner 2 is positioned opposite the thrust 3 that the circlip receives. Good luck and have a nice day. Good luck and have a nice day. Clean the surface of the spark plug 2. After every hour of operation, stop the engine, and then let it cool for five to ten minutes.