Cylinder- 1 intake air pressure sensor hose 16. This system can achieve an optimum air-fuel ratio required by the engine at all times by using a microprocessor that regulates the fuel injection volume according to the engine operating conditions detected by various sensors. Air filter case breather hose 2 13. Adjust the multi-function meter unit panel brightness level by pushing the reset switch. Air temperature sensor lead 7. Stand the vehicle on a level surface. Face the end of the plastic locking tie inward, and then cut off the excess end of the tie.
Start the engine and keep it idling until engine oil starts to seep from the oil gallery bolts. Rider seat bracket assembly 4. When the wheel stops, put an X2 mark at the bottom of the wheel. Align the positioning tape on the starter motor lead with the engine mounting bolt front lower side. Never use solvents on internal brake components. Fuel hose fuel tank to fuel hose joint 5. Measure: Brake disc deflection Out of specification Correct the brake disc deflection or replace the brake disc.
Bleed screw rear brake caliper 6 Nm 0. Position the hose clamp over the white paint mark on the hose, making sure not to install it on the raised portion of the pipe. Throttle cable decelerator cable 7. Rear brake light switch lead 17. Remarks For installation, reverse the removal procedure. Make sure the vehicle is upright.
Pass the O2 sensor lead through the cutout in the heat protector. Direction a Headlight beam is raised. Face the ends of the hose clamp to the left. Cylinder- 1 right ignition coil 30. As the requirements for the engine to deliver more performance and cleaner exhaust gases increase, it becomes necessary to control the air-fuel ratio in a more precise and finely tuned manner. Install: Wheel bearings New Oil seals New a. Fasten the left and right handlebar switch leads at the positioning tape on each lead with a plastic locking tie.
If the marks are not aligned, turn the crankshaft counterclockwise 360 degrees and recheck step b. Check the entire signaling system wiring. Position the accessory light coupler and joint coupler in front of the plate. Therefore, the longer the length of time the fuel injector is energized injection duration , the greater the volume of fuel that is supplied. Install the air vent hose fuel hose joint to fuel tank with its white paint mark facing downward. Please read this material carefully. Tighten: Rear wheel axle nut Rear wheel axle nut 150 Nm 15.
Install: Brake pads Brake pad spring Brake pad pin Brake pad clips Front brake caliper Brake hose guide Brake caliper bolt 40 Nm 4. Install the new wheel bearings and oil seals in the reverse order of disassembly. Bent teeth Replace the rear wheel pulley. Place the other end of the hose into a container. Left handlebar switch lead 3.
Cylinder- 2 intake air pressure sensor hose 3. Outside of the frame S. Put the rocker arm base on the cylinder head. Rear cylinder head cover 10. Throttle cable accelerator cable 3.
Turn the adjusting bolt 1 in direction a or b. Locknut shift rod 12 Nm 1. Check operation, fluid level, and for fluid leakage. Valve guide remover 6 90890-04064 Valve guide remover 6. Detach: Headlight bulb holder 1 5. Therefore, always clean up any spilt brake fluid immediately.
Adjust: Throttle cable free play a. Adjust: Front wheel static balance a. Face the ends of the hose clamp rearward, angled to the left. Do not allow foreign materials to enter the crankcase. Start the engine and let it warm up for several minutes, and then let it run at specified engine idling speed. Cylinder- 1 right ignition coil 7.
All gasket surfaces, oil seal lips and O-rings must be cleaned. Cylinder- 1 intake air pressure sensor 11. Therefore, always clean up any spilt brake fluid immediately. Oil delivery pipe 2 7. Filling fluid The following symbols are used in this manual 3. Numbers 4 are given in the order of the jobs in the exploded diagram. Face the fastener of the clamp to the left.