Note: Your machine is equipped with a circuit breaker that will automatically shut off the brush if a large or loose object is caught in the brush roll. » Do not allow to be used as a toy. Remove and rinse tools in clean, running water. Turn off the machine, and unplug it from the outlet. Plug in and turn on the power switch. Allow to penetrate for at least 3 minutes.
Before you place the cleaned 2-in-1water tank back onto the machine, simply unscrew the nozzle using a Phillips head screwdriver This can be rinsed out at the faucet. Dirty water pulled out of your carpets will collect around the outside of the bladder so that clean and dirty water are always kept separate. Coil Flex hose around the Tool Caddy. Simply remove the 2-in-1 Tank and remove the screw to pop out the nozzle for rinsing in the sink. This offers extra protection against dirt and tough stains to Summary of the content on the page No. It is best to begin cleaning in the corner farthest from your exit.
With the applicator tool still on the end of the flex hose, spray clean hand hot tap water into the sink to avoid any future clogging. Remove hard floor tool, rinse and dry before storing. Store applicator tool in a convenient location for use the next time. Simply choose one of the 4 settings heavy traffic, normal clean, light clean, or rinse and the ProHeat 2X will adjust the right amount of cleaning formula to mix with the heated water to fit your cleaning need. It should be set on floor cleaning.
Remove the tank from the base of the machine by lifting up on the tank carry handle. Your ProHeat 2X is well made, and we back it with a limited one-yearwarranty. The inside of the end caps by the brush rolls can be wiped out with a clean paper towel, or, if a more thorough cleaning is desired, the end caps can be taken off using a Phillips head screwdriver and rinsed clean. Do not use a knife or other utensil with sharp edges because it could damage the carpet or upholstery. Pay particular attention to the product diagram, assembly instructions, and part names. Unlatch the top of the Tank from the bottom by lifting the Tank Latch from the bottom at the back of the tank.
Place pivot arm in place and screw in place using the silver screw. If that happens, be sure to unplug your machine, remove the foreign object, and then plug the machine back in to reset the circuit breaker. Advise customer to call Bissell Free Call 1800 number again and press Option 4 for spare parts and order replacement Tank Call Servicing Guide ProHeat 2X 9400F. Be careful not to spray the protector onto furniture or fabric that has not been tested for colorfastness. Before applying Scotchgard protector to a large area, test in a small, hidden area for colourfastness. Screw 3 screws into the marked holes. Fill the heavy duty bladder with clean hand hot tap water.
Also, pop out the red filter underneath the top half of the tank and rinse that out. Repeated strokes in the same Carpet Cleaning area with an ordinary vacu Summary of the content on the page No. Apply Scotchgard protector in a slow sweeping motion with a slight overlap of the treated area. Replace small brush belt, and reverse steps above. Turn the machine on its side. Share the user manual or guide on Facebook, Twitter or Google+.
Place Tank Lid upside down and remove red Lint Filter basket located inside lid on the left hand side Pull red plastic flap up and hold it away from red Lint Filter with one hand. This debris should be picked up and thrown away. Moreover, your cleaning agent is not wasted, as there are two separate tanks for storing water and cleaning solution. Remove hard floor tool, rinse and dry before storing. Snap tools into the tool caddy as shown in figure 5. Rinse optional and suction as needed. Vacuum or sweep thoroughly to Summary of the content on the page No.
Turn the machine on its side. Because the water and formula are stored separately, they are not mixed until you are ready to clean. Rinse out the formula tank. Turn the Power Switch and Heater On. Place cleaned or new brush rolls back onto the rods. Set Ready Tools dial to either floor cleaning or hose attachments setting.
Note how the lip on the top tank separates from the groove in the bottom tank. Use a vacuum with a brush attachment and a crevice tool to clean in fabric folds. Screw in with 3 screws. Do not use on Velvet or Silk. Tank may not be assembled properly. Fill up the 2-in-1Tank by removing the Tank from the base of the machine with the Tank Carry Handle.