Clean contamination or remove obstruction in the paper path. Press on the flat side of the Roll Assembly Feed away from the shaft. Electronic bulletin board system An electronic bulletin board system. Pull the Latch R off of the Shaft Latch. Can be selected only if the optional lower cassette unit C812902 is installed. When the Cover is open, the tab of the Cover releases the floating idler gear.
Remove the one screw that retains one end of the Fuse to the Fuser Frame. Do not expose yourself to the laser beam to prevent injury blindness. Hold the metal tabs attached to the ends of the Heater Quartz and carefully slide the Heater Quartz out of the Roll Fuser. Slide the Guide R A and B out of the slot in the Printer Frame. Remove the Kit Chute Registration Assembly. Remove the Cover Assembly, E.
Does the printer still exhibit erratic operation? Remove Roll Assembly Exit Out. Then manually rotate the assembly. The table below lists all messages displayed by the printer. F-4 Map of SelecType Menus. Go to step 1 3.
Cleaning Blade: Scrapes the toner remaining after the Transfer step off of the Drum surface. To cancel this mode, you must switch the printer off. Remove the Cover Assembly, E. Toner life will vary according to print coverage and printing method continuous or intermittent, print density, toner-save mode, etc. Take care to avoid catching hands in movable parts rollers, fan, etc. In addition to the descriptions below and those given in this manual, there are many situations and circumstances that are dangerous. One or more of these components may have failed partially or completely.
It has excellent monochromaticity and convergence. The mirror reflects the laser beam produced by the laser diode so that the beam scans across the drum surface. As indicated in the table below. Press the Bearing Feed away from the Roll Assembly Feed to pull off the latches 1 at the bottom part of the Bearing Feed. If you can not isolate the problem using this procedure, replace each components listed below, one at a time, until the problem disappears. Remove the Cover Side, E.
Getting Started 7 Laser safety labels w Warning: Use of controls, adjustments, or performance of procedures other than those specified in this guide may result in hazardous radiation exposure. Are these rolls free of scratches and contamination? Remove the two screws 1 that are located at the rear of the Cover Side,E. This pin transmits data from the computer to the printer. Remove the screw that secures the Latch R to the Shaft Latch. Turn the Fuser Assembly upside down.
One or more of these components may have failed partially or completely. Permanently relocate either the printer or the problem devices. Print test image and turn off the printer halfway through the print cycle. Remove the six screws that secure the Angle to the Printer Frame. Remove the Cover Assembly, E. Exit Cam Interlock Switch Cover Assy. The dots can be close together to create black or more widely spaced to create gray or white areas in the image.
Remove the Cover Assembly, E. Remove the Actuator No Paper 4. Remove the Cover Assembly, E. Set the printer on the left surface. Remove the two screws that secure the Solenoid Exchange Direction solenoid to the Printer Frame. The following flowchart show the disassembly flow. Is the Electrical Noise problem still present? Release the hook on the interior surface of the top side of the Cover Side by pulling the edge of the top side 2 up, and then pull the Cover Side away from the printer.
D Working with Fonts D-1 Appendix D Working with Fonts Printer and Screen Fonts. If you need to touch these areas, wear appropriate electrostatic protection gear electrostatic wrist band, etc. Remove the two screws that secure the Chute Inlet Registration to the Angle and separate the Chute from the Angle. Remove the Kit Chute Registration Assembly. The hole is located immediately in front of the Fuser Assembly. Is the print image normal? Take the board out of the Shield Assembly Bottom E sliding it backward to the left. Remove the Control Assembly Panel E.
Stores setup parameters related to engine control. Remove the Control Assembly Panel E. Because of its convergence characteristic, the laser beam converges into one point, causing high density and high temperature. Disconnect P234 and P236 from the Sensor Assembly Size-1 ,E. D Working with Fonts D-5 I239X mode To see the font samples, use the Test Menu in SelecType. Carefully manipulate the Cover Exit,E to move the Bracket Hinge away from the mount toward you and then raise the right side of the Cover Exit to tilt the Cover Exit 1.